How To Install A WPC Door Frame: Step-By-Step Guide

Greenplastwood · SNG Eco India Pvt. Ltd. · Updated October 2026

A WPC door frame is installed in the same way as a wooden frame, using the same saw, drill and screws. The difference is that WPC needs no termite treatment and no polishing after installation. The diagrams in this guide are taken from the installation guide in our company profile.

WPC door frame fixed plumb in a wall opening and checked with a spirit level
A WPC door frame being fixed in the wall and checked with a spirit level.

Before You Start

  • Check that the frame size matches the wall thickness and the door you plan to fit.
  • Check the opening: it should be clean, and wide and tall enough for the frame.
  • Store the frames flat in a dry, shaded place until they are installed.
  • Plan to fix the frame before plastering and tiling are finished around it.

What You Need

  • Two vertical posts and one head piece in the required frame size
  • A fine-tooth saw or a mitre saw
  • A drill, screws and wall plugs or hold-fasts
  • A spirit level and a measuring tape

Step 1: Cut The Posts And Head

Cut both vertical posts to the height of the opening and the head piece to its width. Allow for the type of corner joint you plan to use.

WPC door frame cutting type 1
WPC door frame cutting type 2
WPC door frame cutting type 3
WPC door frame cutting type 4
WPC door frame cutting type 5

For clean cuts: measure twice and mark the cut with a pencil, use a fine-tooth blade, and support the full length of the profile while cutting so it does not vibrate.

Step 2: Make The Corner Joints

Join the head piece to the posts using one of the standard joints shown below. Always secure the joint with screws rather than relying on adhesive alone.

WPC door frame joint type 1
WPC door frame joint type 2
WPC door frame joint type 3
WPC door frame joint type 4
WPC door frame joint type 5

Drill pilot holes before driving the screws into the joint. This gives a tight, clean joint and keeps the edges neat.

Step 3: Fix The Frame In The Wall

Place the frame in the opening and check both posts with a spirit level. Fix the frame to the wall and make sure it stays square, so the door opens and closes evenly.

WPC door frame fixed in a wall opening, example 1
WPC door frame fixed in a wall opening, example 2
WPC door frame fixed in a wall opening, example 3
WPC door frame fixed in a wall opening, example 4
WPC door frame fixed in a wall opening, example 5

To confirm that the frame is square, measure both diagonals of the opening; they should be equal. Fix each post to the wall at several points along its height, and keep the frame braced until the plaster around it has set.

Tip: in bathrooms, install the frame before tiling so the tiles can finish neatly against it.

Installing In Bathrooms And Wet Areas

WPC is well suited to bathrooms, toilets and kitchens because it does not absorb water. Fix the frame before the floor and wall tiles are laid, so the tiles can be finished neatly against it. Keep the bottom of the frame clean of cement and debris, and seal the joint between the frame and the tiles with a suitable sealant for a clean, watertight finish.

Fitting The Door

Once the frame is fixed and the plaster has set, hang the door on hinges screwed into the frame, using pilot holes for each screw. Check that the gap between the door and the frame is even on all sides and that the door closes smoothly before fitting the lock.

Common Mistakes To Avoid

  • Skipping the spirit level check, which leads to a door that does not close evenly.
  • Relying only on adhesive at the corner joints instead of screws.
  • Installing the frame after tiling, which leaves uneven edges around it.
  • Leaving the frame uncovered during plaster and paint work. Protect it with tape or a cover sheet.

After Installation

Wipe the frame with a damp cloth to remove dust. If a different shade is required, the frame can be painted, polished or laminated. No termite treatment or regular polishing is needed.

Common Questions

Does The Carpenter Need Special Tools?

No. WPC is cut, drilled, screwed and nailed with the same tools that are used for wood.

Can A WPC Frame Replace An Old Wooden Frame?

Yes. Remove the old frame, clean and prepare the opening, and follow the same steps. Choose a size that matches the existing wall thickness.

Are Window Frames Installed The Same Way?

Yes. WPC window frames and shutters are cut, joined and fixed in the same way as door frames.